Its_All.Lost
Because hope just breeds everlasting misery…

Gulfcoast Robotics Carriage Cable Chain

Gulfcoast Robotics Carriage Cable Chain

The Monoprice Maker Select v2.1 comes with cable chains on the X and Z-axis, but not the Y-axis. I have no idea why. It has been on my list of to-do items to add a cable chain to the Y-axis, but I have just never gotten around to do it. About a year ago or so I managed to get around to printing the cable chain links and mounts but I never installed any of it. Fast forward to present day and I find myself wanting to tinker with the printer and have been thinking of new upgrades for it. Thats when I spotted the chain that I had printed in a box. I originally printed the chain to mount to the printer and to the stock carriage, but I no longer have that carriage. Now I have a carriage from Gulfcoast Robotics, so what I already printed doesn’t fit.

Off to Tinkercad!

I have previously designed a handle for the new Gulfcoast carriage that just slips on, I added a zip-tie to keep it from accidentally falling off and it works great! So I figured I could take that designed and remix it to work for me as a contact point for the heatbed cable chain. A day or two and 6 prints later and I have a slip-on cable chain for the Maker Select. I remixed a rear frame mount so that no screws are needed, just slide the piece over the bracket. The same goes for the bed carriage, just slide it on. I did add a zip-tie to make sure it doesn’t pop off, because it is a pain to put on. I used the existing chain links that I had already printed and it all came together.

The one thing I did not think about was the offset that the chain would have. The original mount that uses screws mounts to the same place as the Y-axis stepper motor and this is centered with the bed and the wiring. Adding a cable chain here you are going to get a nice straight line. I am using a slip-on rear mount so I cannot center it due to the stepper being in the way. Luckily I had two offset links printed from back then. Like it was meant to be. I still need to print one more but it works fine it just looks a little odd because of the way the chain is offset.

 

Maker Select Gulfcoast Robotics Heatbed Cable Chain (my cable chain mounts) https://www.thingiverse.com/thing:4644050

The cable chain links to make the chain https://www.thingiverse.com/thing:1060522

Y-axis cable chain mount for MP Maker Select (the thing I based my remix off of) https://www.thingiverse.com/thing:2221459

 

 

Wanhao/Monoprice Y-carriage and heatbed upgrade

Upgrade

So I made the jump and upgraded a bunch of shit. I did it for smoother bottom first layer prints (because of the glass) and hopefully no more curling issues. I upgraded to the “Anycubic Ultrabase 3D Printer Platform with Aluminum 12V/24V Dual Power MK3 Heatbed” and while I was at it I upgraded to the Gulfcoast Robotics Y-axis carriage too, as I have read it is wise to do both at the same time and the stock bed plate is usually warped from posts I come across constantly. In fact I went a step further and bought new 40mm and 80mm Noctua fans for the printer too! Happy upgrade day!

I am going to use the 40mm to replace the stock 40mm extruder cooling fan and the 80mm to replace the control box fan(s). I printed a new backplate for the printer. I dug through Thingiverse for a bit and chose one that looked like it had a following and worked well. After printing it I realized I should have maybe dug a little more, it was not easy to install. In fact I didn’t install all of the screws back on because I cannot get an allen wrench in there to do it. But it does the job, and man are those Noctua fans fucking quiet!! If it is sitting idle I cannot tell it is on, it is in my living room. I hear if you upgrade to TMC2130 drivers (with a RAMPS board) then it is this quiet while printing too. Damn!.

I decided to write this up real quick because when I searched for relative content I found shit on it. Searches for Anycubic turns up their printers, so searching for the bed/covering/plate was a pain in the ass. All I found was this. I ended up figuring it out as it’s not that hard but if i was able to read something on it first I probably would have saved my ass about 3-4 hours of head scratching.

View Post